Cart
Pack Seal
Applying a seal – or gasketing - around a battery pack prevents contamination from environmental hazards and water intrusions.
Solutions for Sealing Battery Packs
Achieving a quality seal is critical for the performance, longevity, and protecting components of the battery from water and other harsh environmental conditions.
Battery pack seals or gaskets must meet design and regulatory enclosure standards. For example, an IP68 rating means that the seal will protect against water intrusions, corrosion, and outside contaminants.
Manufacturers meet these standards by robotically dispensing a bead of one or two component material around the perimeter of the battery pack in one of two ways:
- Cure in place gasketing (CIPG): The dispensed material cures before assembly, creating a compression gasket in the pack seal joint.
- Form in place gasketing (FIPG): The material is dispensed and assembled immediately, allowing the material to cure over time.
To ensure a durable, reliable seal, gasketing must be clean, precise and repeatable. Bead placement, flow rate, volume of material dispensed, and mix ratios for two component materials are critical.
Discover Solutions for Pack Seal (Gasketing)
These products are a representation of possible options for your finished system. Your solution is configured for your specific needs.
Supply
Dispensing Systems
Dispense Valves
Related Articles
Battery Pack Seal - EV Battery
A quality seal is critical for the performance and longevity of EV batteries and for protecting integral components from water intrusion and other harsh environmental conditions.
Knit Line Dispense Techniques
Learn about different dispense and automation techniques for cure-in-place and form-in-place gasketing and how it impacts the fusion of the bead.
Related Materials
Parker LORD Sipiol UV
Sipiol UV was developed specifically for electric vehicle (EV) battery applications. It cures in seconds with UV light, and is electrically insulative.
PPG CoraChar SE 4000
PPG CoraChar SE 4000 intumescent fire protective coating shields electric vehicle (EV) battery packs and electrical energy components from external fires and internal thermal runaway events.
Sika Sikagard-834
Sikagard 834 epoxy-based intumescent fire protection coating protects electric vehicle (EV) batteries from thermal events.
Tflex CR607
At 6.4 W/m-K thermal conductivity, Tflex™ CR607 is at the forefront of thermal performance for a two-part, cure in place dispensable gap filler.
VM 1802
LG Chem VM 1802, a two-component thermal material for EV Battery and Electronics heat transfer applications.
Liqui-Form 3500 (LF3500)
Henkel - BERGQUIST® LIQUI-FORM 3500 is a high conductivity gel thermal interface material designed for demanding applications that require a balance between dispensability and low component stress during assembly.
HB Fuller EV Protect 4006
EV Protect 4006 is a two-component flame retardant, low-density polyurethane foam designed for potting and encapsulation of cylindrical cells in EV battery modules.
HB Fuller EV Seal 500
Learn more about EV SEAL 500, an easy to apply, fast setting, and resealable gasket material used in automotive and EV battery applications.
LORD CoolTherm SC-1200
Since CoolTherm® SC 1200 thermally conductive silicone gap filler is highly abrasive, Parker LORD® asked Graco to find out how to dispense one million shots of the two component material without equipment failure.
LORD CoolTherm TC-2002
Parker Lord CoolTherm® TC-2002 adhesive is a two-component adhesive system designed for use in structural bonding applications which require thermal conductivity with high bond strength.
Dow SYLGARD 170
SYLGARD™ 170 Fast Cure Silicone Elastomer is a two-part general purpose encapsulant with low viscosity, good flow ability, and flame resistance that cures fast at room temperature.
Dow Dowsil EF-6525 RTV Low-Viscosity Silicone Foam
DOWSIL™ EF-6525 RTV Low Viscosity Silicone Foam is a two-component low-density liquid elastomer that cures into a foamed elastomer.
