SDP-3540 A/B

Liquid-dispensed gap filling rubber | Shin-Etsu

Shin-Etsu

Shin-Etsu SDP-3540 A/B

PRODUCT DESCRIPTION:

Shin-Etsu's SDP-3540 A/B is a UL-94 V-0 equivalent, dual component, heat or room-temperature cured product that acts as a thermal interface gap filler and provides superior thermal conductivity, excellent electrical insulation, and low thermal resistance.

Material supplier:

Shin-Etsu

Industry:

Electronics

Application:

Thermal dissipation

Material specs:

SDP 3540 A/B

 

Typical properties

  • Type: Liquid-dispensed gap filling rubber
  • Cure type: Addition
  • One or two component? Two
  • Low molecular weight siloxane stripped? Yes
  • Colour: Grey
  • Density @ 23C (g/cm3): 3.08
  • Viscosity (Pa*s): 89
  • Mix ratio by weight: 100:100
  • Cure conditions: 24hr @ 25°C
  • Working time: 4 hours
  • Thermal conductivity (W/mk): 3.5
  • Thermal resistance (mm2*K/W): 37
  • Usable temp. Range (C): -40 to 180°C

Graco Equipment recommendations:


UniXact C300 automation table:

  • Work envelope: (X-Y-Z): 254 mm x 277 mm x 70 mm (10 in x 11 in x 2.75 in) 
  • Approximate overall dimensions: 1905 mm x 939 mm x 1041 mm (75 in x 37 in x 41 in) 
  • Drive method: ball screw drives with linear guide bearings
  • Drive system: servo drive motors for X, Y, Z, and theta (dispense)
  • Accuracy: +/- 0.1 mm/300 mm (+/- 0.004 in/12 in)
  • Position repeatability: 0.01 mm (0.0004 in)
  • Dispense speed: 100 mm/s (4 in/s)

Graco PD44 patented metering, mix and dispense valve for two-component micro dispensing

The Graco PD44 is designed to accurately dispense two-component epoxies, urethanes, silicone and most reactive resin systems in small amounts from 0.005 cc to 5 cc. Discover more about the PD44 metering, mix & dispense valve.

  • Specifically designed to accurately dispense shots of two-component epoxies, urethanes, silicone and most reactive resin systems
  • Improved low-viscosity spool design
  • Rod positive displacement metering
  • Precise mix ratio and shot repeatability
  • Eliminates cleaning and potential hardening of materials in the valve

Graco PR-X metering, mix and dispense system

  • Specifically designed to precisely dispense shots of two-component sealants and adhesives when tight ratio tolerances are required
  • Provides superior control and repeatability for beads, dots, and other patterns to ensure specifications are always met
  • Long-lasting on-ratio dispensing with minimal recurring maintenance
  • Engineered coatings and fluid path geometry specifically designed to resist wear from abrasive materials
  • Flexible in raw material delivery and dispensing, and in installation options
  • System configurations include cartridge or supply feed and direct or remote mounted dispense valve

For complete product information, please refer to www.shinetsusilicones.com.

Download the spec. sheet

Contact an expert

Please enter a value
Please select
Please enter a value
Please enter a value
Please select
Please enter a value
Please enter a value

Recommended products

For applying SDP-3540 A/B

Do You Have Product Questions?

Technical Support

Technical Support

+32 89 770 847

Monday - Friday
8:30 - 17:00 CET

General Support

General Support

+32 89 770 865

Monday - Friday
8:30 - 17:00 CET

Graco