Choosing the Right Pump for Euclid Products

Pump Selection Based on Mortar Application

When switching from hand-applying to pumping or spraying a mortar-based material, it's important to select the right equipment for the job. Below are Euclid Chemical materials that have been field tested with Graco pumps so you know what works best and are set up for success.

Should you have questions or would like to talk to an expert about a material not listed here, please fill out the form on this page and we will get you in touch with a Graco representative.
 

Cement-Based Waterproofing Finish

MaterialPumpPowerHoseMinimum
Compressor
Spraying
TamosealT-MAX 6912110 V

15.24 m (50') of 1" hose + 3.05 m (10') of 3/4" hose169.9 m3/hr (100 CFM), 6.2 bar (90 PSI)5.5-6.9 bar (80-100 PSI)

Epoxy Coating

MaterialPumpPowerHoseMinimum
Compressor
Spraying
Duralkote 240ToughTek M680aPneumatic15.24 m (50') of 1" hose +3.05 m (10') of 3/4" hose169.9 m3/hr (100 CFM), 6.2 bar (90 PSI)HTX with 4mm orifice
Duralkote 500ToughTek M680aPneumatic15.24 m (50') of 1" hose +3.05 m (10') of 3/4" hose169.9 m3/hr (100 CFM), 6.2 bar (90 PSI)HTX with 4mm orifice

Repair Mortar

MaterialPumpPowerHoseMinimum
Compressor
Spraying
Tamms Structural MortarToughTek S340e220 V/110 V15.24 m (50') of 1 3/8" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)1/4" orifice spray wand
Tamms Structural MortarToughTek M680a220 V/Pneumatic15.24 m (50') of 1" hose +3.05 m (10') of 3/4" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)

1/4" orifice spray wand
EucoRepair V100ToughTek S340e220 V/110 V15.24 m (50') of 1 3/8" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)1/4" orifice spray wand
EucoRepair V100ToughTek M680220 V/Pneumatic15.24 m (50') of 1 3/8" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)1/4" orifice spray wand
EucoRepair SCCToughTek P30HT220 V15.24 m (50') of 1 3/8" hosen/an/a
Versaspeed LS 100ToughTek P30HT220 V15.24 m (50') of 1 3/8" hosen/an/a
      

Self-Levelling Underlay

MaterialPumpPowerHoseMinimum
Compressor
Spraying
Super Flo TopToughTek MP40220 V30.5 m (100') of 1 3/8" hosen/an/a
Eucofloor SL160ToughTek MP40220 V30.5 m (100') of 1 3/8" hosen/an/a
Level Top StainToughTek MP40220 V30.5 m (100') of 1 3/8" hosen/an/a
Level Top PolishToughTek MP40220 V30.5 m (100') of 1 3/8" hosen/an/a
Level Top PC-AGGToughTek MP40220 V30.5 m (100') of 1 3/8" hosen/an/a
Level Top PC-AGGToughTek P30HT220 V76.2 m (250') of 1 3/8" hosen/an/a
      

Stampable Overlay (Grout)

MaterialPumpPowerHoseMinimum
Compressor
Spraying
Thin-Crete Vertical GroutToughTek S340e220 V/110 V15.24 m (50') of 1 3/8" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)1/2" orifice spray wand full pressure
      

Water-Based Acrylic Coating

MaterialPumpPowerHoseMinimum
Compressor
Spraying
TammscoatT-MAX 6912110 V15.24 m (50') of 1" hose + 3.05 m (10') of 3/4" hose169.9 m3/hr (10 CFM), 2.76 bar (40 PSI)5.5-6.9 bar (80-100 PSI)
      

WATCH: ToughTek Successfully Pumps Euclid Chemical Mortar Materials

 

Contact an Expert

Please enter a value
Please enter a value
Please select
Your email address is required
Please enter a value
Please enter a value
Please enter a value

Have Questions? Let's Talk.

Contact an expert

Contact an expert

We'll help you choose the right product for your job.

Email Support

Email Support

Graco